华擎z77错误代码

以下为您整理了华擎z77错误代码的答案

华擎Z77主板，板载故障码d6，蜂鸣器短鸣4次。是什么问题

如果电脑有故障，它可通过摩斯密码告诉，电脑的毛病出在哪里。PC喇叭的开机警报判断问题 1声短鸣：

内存刷新失败。 2声短鸣：

内存ECC校验错误。 3声短鸣：

系统基本内存(

第1个64KB容量)自检失败。 4声短鸣：

系统时钟出错。 5声短鸣：

CPU出错。 6声短鸣：

键盘控制器错误。 7声短鸣：

系统实模式错误，不能进入保护模式。 8声短鸣：

显示内存错误(如显示内存损坏)。 9声短鸣：

主板FlashROM或EPROM检验错误(例如BIOS被CIH病毒破坏)。 1长3声短鸣：

内存错误(例如内存芯片损坏)。 1长8声短鸣：

显示系统测试错误(如显示器数据线或显示卡接触不良)。 Award BIOS 1声短鸣：

系统正常启动。 2声短鸣：

常规错误。应进入CMOSSETUP，重新设置不正确的选项。 1声长鸣1短声鸣：

内存或主板出错。 1声长鸣2短声鸣：

显示器或显示卡错误。 1声长鸣3声短鸣：

键盘控制器错误。 1声长鸣9声短鸣：

主板FlashRAM或EPROM错误(例如BIOS被CIH破坏)。 不间断长嘟声：

内存未插好或有芯片损坏。 不停响声：

显示器未与显示卡连接。 重复短嘟声：

电源有故障。 无嘟声同时无显示：

主板电源未接通，或电源损坏。

华擎z77板子奇怪问题求助

电源功率不够，所以重启时点不亮，你换个大功率的电源就行

请问一下我的华擎z77极限玩家6点不亮debug显示00是什么问题，在线等，急！修好重赏！

CPU没有供电，主板的问题

哪位大神知道华擎Z77Professional这块板子的故障代码

官网上使用手册内有故障代码，如下截图：

华擎Z77极限玩家4主板故障代码大全

其实这个官网上下载说明书就有的。下面附上。Status Code Description0x00 Not used0x01 Power on. Reset type detection (soft/hard)0x02 AP initialization before microcode loading0x03 North Bridge initialization before microcode loading0x04 South Bridge initialization before microcode loading0x05 OEM initialization before microcode loading0x06 Microcode loading0x07 AP initialization after microcode loading0x08 North Bridge initialization after microcode loading0x09 South Bridge initialization after microcode loading0x0A OEM initialization after microcode loading0x0B Cache initialization0x0C – 0x0D Reserved for future AMI SEC error codes0x0E Microcode not found0x0F Microcode not loaded0x10 PEI Core is started0x11 Pre-memory CPU initialization is started0x12 Pre-memory CPU initialization (CPU mole specific)0x13 Pre-memory CPU initialization (CPU mole specific)0x14 Pre-memory CPU initialization (CPU mole specific)0x15 Pre-memory North Bridge initialization is started0x16 Pre-Memory North Bridge initialization (North Bridge mole specific)0x17 Pre-Memory North Bridge initialization (North Bridge mole specific)0x18 Pre-Memory North Bridge initialization (North Bridge mole specific)0x19 Pre-memory South Bridge initialization is started0x1A Pre-memory South Bridge initialization (South Bridge mole specific)0x1B Pre-memory South Bridge initialization (South Bridge mole specific)0x1C Pre-memory South Bridge initialization (South Bridge mole specific)0x1D – 0x2A OEM pre-memory initialization codes0x2B Memory initialization. Serial Presence Detect (SPD) data reading0x2C Memory initialization. Memory presence detection0x2D Memory initialization. Programming memory timing information0x2E Memory initialization. Configuring memory0x2F Memory initialization (other)0x30 Reserved for ASL0x31 Memory Installed0x32 CPU post-memory initialization is started0x33 CPU post-memory initialization. Cache initialization0x34 CPU post-memory initialization. Application Processor(s) (AP) initialization0x35 CPU post-memory initialization. Boot Strap Processor (BSP) selection0x36 CPU post-memory initialization. System Management Mode (SMM)initialization430x37 Post-Memory North Bridge initialization is started0x38 Post-Memory North Bridge initialization (North Bridge mole specific)0x39 Post-Memory North Bridge initialization (North Bridge mole specific)0x3A Post-Memory North Bridge initialization (North Bridge mole specific)0x3B Post-Memory South Bridge initialization is started0x3C Post-Memory South Bridge initialization (South Bridge mole specific)0x3D Post-Memory South Bridge initialization (South Bridge mole specific)0x3E Post-Memory South Bridge initialization (South Bridge mole specific)0x3F-0x4E OEM post memory initialization codes0x4F DXE IPL is started0x50 Memory initialization error. Invalid memory type or incompatible memoryspeed0x51 Memory initialization error. SPD reading has failed0x52 Memory initialization error. Invalid memory size or memory moles do notmatch0x53 Memory initialization error. No usable memory detected0x54 Unspecified memory initialization error0x55 Memory not installed0x56 Invalid CPU type or Speed0x57 CPU mismatch0x58 CPU self test failed or possible CPU cache error0x59 CPU micro-code is not found or micro-code update is failed0x5A Internal CPU error0x5B reset PPI is not available0x5C-0x5F Reserved for future AMI error codes0xE0 S3 Resume is stared (S3 Resume PPI is called by the DXE IPL)0xE1 S3 Boot Script execution0xE2 Video repost0xE3 OS S3 wake vector call0xE4-0xE7 Reserved for future AMI progress codes0xE8 S3 Resume Failed0xE9 S3 Resume PPI not Found0xEA S3 Resume Boot Script Error0xEB S3 OS Wake Error0xEC-0xEF Reserved for future AMI error codes0xF0 Recovery condition triggered by firmware (Auto recovery)0xF1 Recovery condition triggered by user (Forced recovery)0xF2 Recovery process started0xF3 Recovery firmware image is found0xF4 Recovery firmware image is loaded0xF5-0xF7 Reserved for future AMI progress codes0xF8 Recovery PPI is not available0xF9 Recovery capsule is not found0xFA Invalid recovery capsule0xFB – 0xFF Reserved for future AMI error codes0x60 DXE Core is started0x61 NVRAM initialization440x62 Installation of the South Bridge Runtime Services0x63 CPU DXE initialization is started0x64 CPU DXE initialization (CPU mole specific)0x65 CPU DXE initialization (CPU mole specific)0x66 CPU DXE initialization (CPU mole specific)0x67 CPU DXE initialization (CPU mole specific)0x68 PCI host bridge initialization0x69 North Bridge DXE initialization is started0x6A North Bridge DXE SMM initialization is started0x6B North Bridge DXE initialization (North Bridge mole specific)0x6C North Bridge DXE initialization (North Bridge mole specific)0x6D North Bridge DXE initialization (North Bridge mole specific)0x6E North Bridge DXE initialization (North Bridge mole specific)0x6F North Bridge DXE initialization (North Bridge mole specific)0x70 South Bridge DXE initialization is started0x71 South Bridge DXE SMM initialization is started0x72 South Bridge devices initialization0x73 South Bridge DXE Initialization (South Bridge mole specific)0x74 South Bridge DXE Initialization (South Bridge mole specific)0x75 South Bridge DXE Initialization (South Bridge mole specific)0x76 South Bridge DXE Initialization (South Bridge mole specific)0x77 South Bridge DXE Initialization (South Bridge mole specific)0x78 ACPI mole initialization0x79 CSM initialization0x7A – 0x7F Reserved for future AMI DXE codes0x80 – 0x8F OEM DXE initialization codes0x90 Boot Device Selection (BDS) phase is started0x91 Driver connecting is started0x92 PCI Bus initialization is started0x93 PCI Bus Hot Plug Controller Initialization0x94 PCI Bus Enumeration0x95 PCI Bus Request Resources0x96 PCI Bus Assign Resources0x97 Console Output devices connect0x98 Console input devices connect0x99 Super IO Initialization0x9A USB initialization is started0x9B USB Reset0x9C USB Detect0x9D USB Enable0x9E – 0x9F Reserved for future AMI codes0xA0 IDE initialization is started0xA1 IDE Reset0xA2 IDE Detect0xA3 IDE Enable0xA4 SCSI initialization is started0xA5 SCSI Reset450xA6 SCSI Detect0xA7 SCSI Enable0xA8 Setup Verifying Password0xA9 Start of Setup0xAA Reserved for ASL (see ASL Status Codes section below)0xAB Setup Input Wait0xAC Reserved for ASL (see ASL Status Codes section below)0xAD Ready To Boot event0xAE Legacy Boot event0xAF Exit Boot Services event0xB0 Runtime Set Virtual Address MAP Begin0xB1 Runtime Set Virtual Address MAP End0xB2 Legacy Option ROM Initialization0xB3 System Reset0xB4 USB hot plug0xB5 PCI bus hot plug0xB6 Clean-up of NVRAM0xB7 Configuration Reset (reset of NVRAM settings)0xB8 – 0xBF Reserved for future AMI codes0xC0 – 0xCF OEM BDS initialization codes0xD0 CPU initialization error0xD1 North Bridge initialization error0xD2 South Bridge initialization error0xD3 Some of the Architectural Protocols are not available0xD4 PCI resource allocation error. Out of Resources0xD5 No Space for Legacy Option ROM0xD6 No Console Output Devices are found0xD7 No Console Input Devices are found0xD8 Invalid password0xD9 Error loading Boot Option (LoadImage returned error)0xDA Boot Option is failed (StartImage returned error)0xDB Flash update is failed0xDC Reset protocol is not available

华擎axtu出现错误求大神解决！！！

华擎超级调节工具AXTU是一个全功能软件，可让您在友好的界面中微调各个不同功能，包括硬件监控，风扇控制，超频，OC DNA和IES。在硬件监控方面，它可显示您系统的主要参数。风扇控制方面，它可显示风扇转速和温度，方便您调节。超频方面，您可以调节GT频率与一些电压参数以获得最佳系统性能。OC DNA功能可让您保存您的超频设置，并与朋友分享。您的朋友可以将您的超频设置载入他们的系统中，获得跟您一样的超频设置。在Intelligent Engergy Saver智能节电模式方面，电压调整器会在处理器核心闲置时，自动降低输出电源相位以提高效率，却完全不损失运算性能。 首屏是基本硬件监控状态信息，显示CPU频率、温度、风扇转速、南北桥、内存电压等等 这一界面可调风扇转速，不过前提是风扇为4Pin设计，支持转速调节。如果是3Pin设计且主板不支持电流调速的话，怎么调都不会有反应的 超频设置简单直观，可调选项一一列出 OC DNA功能可让您保存您的超频设置，并与朋友分享。您的朋友可以将您的超频设置载入他们的系统中，获得跟您一样的超频设置。 在Intelligent Engergy Saver智能节电模式方面，电压调整器会在处理器核心闲置时，自动降低输出电源相位以提高效率，却完全不损失运算性能。综合来看，华擎AXTU工具中规中矩，基本上是BIOS中超频功能的Windows移植版，UI更友善，用户体验也相对好很多。近期华擎在发布BIOS更新的时候，也提示用户如果想完美支持Ivy Bridge CPU，除更新BIOS外，安装Intel ME驱动和AXTU工具也是必须的，想必AXTU有过人之处，华擎主板用户不妨安装体验一下。该工具只支持华擎主板，型号支持列表如下：

Asrock 970 Extreme3, 990FX Extreme3, 990FX Extreme4, A55M-VS, B75 Pro3, B75 Pro3-M, B75M, B75M-ITX, E35LM1, H61iCafe, H61DE/S3, H61DEL, H61M, H61M-GE, H61M-GS, H61M-HVS, H61M-HVGS, H61M-S, H61M/U3S3, H61M-VS, H61M-PS2, H67DE3, H67M, H67M-GE, H67M-GE/HT, H67M-ITX, H67M-ITX/HT, H77M, H77M-ITX, H77 Pro4/MVP, H77 Pro4-M, P67 Extreme4, P67 Extreme4 Gen3, P67 Extreme6, P67 Pro, P67 Pro3, P67 Pro3 SE, P67 Transformer, Q77M vPro, Z68 Extreme3 Gen3, Z68 Extreme4, Z68 Extreme4 Gen3, Z68 Extreme7 Gen3, Z68M-ITX/HT, Z68M/USB3, Z68 Pro3, Z68 Pro3 Gen3, Z68 Pro3-M, Z68M/USB3, Z68M-ITX/HT, Z75 Pro3, Z77 Extreme4, Z77 Extreme4-M, Z77 Extreme6, Z77 Pro3, Z77 Pro4, Z77 Pro4-M, Z77E-ITX, X79 Extreme3, X79 Extreme4, X79 Extreme4-M, X79 Extreme6, X79 Extreme6/GB, X79 Extreme7 et X79 Extreme9适用于如下操作系统：

WinXP-32WinXP-64Vista-32Vista-64Win7-32Win7-64AXTU

0.

1.

219版下载地址：

http:

//drivers.mydrivers.com/drivers/444-177938-ASRock-Extreme-Tuning-Utility(AXTU)-0.

1./‍

提示:想了解更多华擎z77错误代码相关的内容,请尝试通过上方搜索框搜索。